A Safe, Energy-Saving and Environmentally Friendly Flow Control Solution Expert

Y Type Strainer

  • JGD-D1 type rubber cutting vibration isolator

    JGD-D1 type rubber cutting vibration isolator

    Product introduction D1 type rubber cutting vibration isolator is composed of internal and external steel bushing and medial synthetic rubber, after vulcanization, it appears a core in the middle and the rubber part is stressed, and there are large deformation range and low free -running frequency. The working temperature ranges -5C~+50C, as the temperature changes, the rigidity changes; damping ratio is C/CC>0.07. It has good vibration isolating effect for the active vibra...
  • 7901 Grooved Ends Y-type Strainer

    7901 Grooved Ends Y-type Strainer

    Specifications NPT or BSPT blowoff outlet on cover. Blowoff outlets are finished with plugs. Screens are perforated 304 stainless steel with spot welded seam. Recessed seat in body assures accurate screen alignment. Groove dimensions comply with Metric or AWWA C606 standard. Working Pressure and Temperature 16 bar/250 psi rated at -10°C to 120°C. Corrosion Protection Fusion bonded coating or liquid epoxy painted interior and exterior. ...
  • 7701 Threaded Ends Y-type Strainer

    7701 Threaded Ends Y-type Strainer

    Detail NPT or BSPT blowoff outlet on cover. Blowoff outlets are finished with plugs. Screens are perforated 304 stainless steel with spot welded seam. Recessed seat in body assures accurate screen alignment. NPT or Metric thread ends. Working Pressure and Temperature 25 bar/300 psi rated at -10°C to 120°C. Corrosion Protection Fusion bonded coating or liquid epoxy painted interior and exterior. Material Specifications Body  ca...
  • 7103 Y-type Strainer

    7103 Y-type Strainer

    Detail BSPT blowoff outlet on cover. Blowoff outlets are finished with plugs. Screens are perforated 304 stainless steel with spot welded seam. Recessed seat in body assures accurate screen alignment. Flanged and drilling complies with EN1092-2 PN16/25. Face to face dimension in accordance with DIN3202 series F1. Working Pressure and Temperature 16 bar rated at -10°C to 120°C for DN50 to DN600. 25 bar rated at -10°C to 120°C for DN50 to DN300. Corrosi...
  • 7101 Y-type Strainer

    7101 Y-type Strainer

    Specifications NPT or BSPT blowoff outlet on cover. Blowoff outlets are finished with plugs. Screens are perforated 304 stainless steewith spot welded seam. Recessed seat in body assures accurate screen alignment. Flanged and drilling complies with EN1092-2 PN16/25; ANSI B 16.1 Class125. WRAS approved: FIG.7101 DN50-DN600 DI body, EPDM gasket for potable water. Working Pressure and Temperature FIG.7101: 16 bar/200 psi rated at -10°C to 120°C for DN50 to DN600. ...
  • GLSY-16 type pull rod companding filter

    GLSY-16 type pull rod companding filter

    Detail Product introduction Construction of GLSY- 16 type pull rod companding filter is similar as GL(y) type filter, just add a set of companding joint combination additional, theory of pollution exclude is similar as GL(y) type filter, it’s convenience for installation Exterior dimension sheet DN (mm) 50 65 80 100 125 150 200 250 300 L 300 350 400 450 500 550 650 775 900 H 130 165 195 230 300 335 420 500 580
  • GL(Y)-16 type filter

    GL(Y)-16 type filter

    Product introduction GL(Y) type filter used for water, oil, gas pipeline and kinds of equipment, it mainly excludes sundries internal of pipeline to protect relief valve, pressure release valve, water, valve and pump etc., it’s installed on outlet, normally screen for water usage adopt10~30 holes/c m2, screen for gas usage adopt 40-100 holes/c m2, screen for oil usage adopt 60- -200 holes/cm2. Technical Parameters 1. Working pressure: 1 .6MPa 2.Teat preci...